- What does an SWR reading of 1 1 mean?
- Does coax length affect SWR?
- What affects SWR?
- Is 1.5 SWR good?
- What does an SWR reading of 4 1 indicate?
- Does a magnetic CB antenna need to be grounded?
- How long should my CB coax be?
- How does high SWR damage a radio?
- Does SWR affect reception?
- Does SWR change with power?
- Is a longer CB antenna better?
- How do I find SWR?
- Why is my SWR so high?
- What SWR is too high?
- What is acceptable SWR?
- How do I know if my CB antenna is bad?
What does an SWR reading of 1 1 mean?
What does an SWR reading of 1:1 mean.
The best impedance match has been attained.
An antenna for another frequency band is probably connected.
No power is going to the antenna..
Does coax length affect SWR?
Many antennas have a SWR of just over a perfect match like a SWR of 1 to 1.2. This is measured at the antenna itself. With a length of coax the SWR will now show a SWR of say 1 to 1.0 , because of the loss in the coax. And so will the bandwidth change a little.
What affects SWR?
There are many things other than the antenna that can cause high SWR. SWR meter readings take into consideration the antenna, the coaxial cable, the mount, the mounting location, the vehicle and objects in the antennas near-field environment.
Is 1.5 SWR good?
SWR RANGE EXPLANATIONS. SWR 1.0-1.5: The ideal range! If your SWR is under 1.5, you’re in great shape. If you’re at 1.5 and really, really want to drop down to closer to 1 it’s likely possible to do with addition tuning, different equipment or a different mounting location.
What does an SWR reading of 4 1 indicate?
What does an SWR reading of 4:1 indicate? Loss of -4 dB. Good impedance match. Gain of +4 dB. Impedance mismatch.
Does a magnetic CB antenna need to be grounded?
Ground Your Antenna Mount If you’re using a standard CB antenna (i.e., anything except a no ground plane, or NGP, kit), you’ll need to make sure your antenna mount is solidly grounded to the vehicle’s chassis. A bad ground will result in an un-tunable antenna and sky-high SWR levels.
How long should my CB coax be?
18 feetSelect the correct coax length. Many antenna manufacturers somewhat pre-tune the antennas utilizing 18 feet of coax which is why we generally recommend 18 feet of coax even if you don’t think that you need that much.
How does high SWR damage a radio?
High SWR can reflect enough power back into the radio to create enough heat to cook the final RF transistor. It isn’t usually an immediate failure, it takes some time for that heat to build up and do damage.
Does SWR affect reception?
Simplified answer: There is no relationship between SWR and receive performance. … SWR is a measure of the impedance mismatch between your antenna and transceiver. Whether transmitting or receiving, a higher SWR correlates with a less efficient coupling of energy between the transceiver and antenna.
Does SWR change with power?
SWR really doesn’t increase with power. It’s always the same.
Is a longer CB antenna better?
Length – Tall antennas generally work better and get a longer range than short antennas. The higher the antenna goes, the farther your message will go, and you can receive messages from farther away. The ideal length antenna for CB radios is 102 inches (about 8 and ½ feet!)
How do I find SWR?
SWR can be calculated from the formula: As you can see by the final expression, SWR and VSWR and ISWR are equal. The smaller the ratio, the better the match between the load and the transmission line. Thus, a 1:1 ratio indicates there are no standing waves and the load is a perfect match.
Why is my SWR so high?
Short. The most common cause of a high SWR is an antenna shorted to ground. There are two places a short can occur in a CB antenna system, in the coax and in the antenna stud.
What SWR is too high?
For instance a SWR too high (over 3:1) all over the band can be an indication of a bad part or junction, poor ground or poor location. An SWR too low over the whole band (1:1 for all 40 channels) can indicate a low efficiency antenna or lossy component. Safe operation of your CB should be with an SWR of 2:1 or less.
What is acceptable SWR?
What is a good SWR reading ? The best reading possible is 1.01:1 (46dB return loss), but usually a reading below 1.5:1 is acceptable. Outside the perfect world a 1.2:1 (20.8dB return loss) is spot on in most cases. To ensure an accurate reading, it is best to connect the meter at the base of the antenna.
How do I know if my CB antenna is bad?
Testing for a Defective CB AntennaUsing your multimeter, touch one of the probes to the metallic end of the antenna. For fiberglass antennas, this will usually be the tunable tip on the antenna’s end. … Touch the other probe to the metallic threads at the end of the antenna. … As you maintain contact with both probes, measure the circuit’s resistance.